Parts catalogue · Boards & RC · Melbourne

Tyre cradle stand, charge-port plug and rail corner guards for self-balancing boards (fits Onewheel GT)

Three accessories for a single-wheel self-balancing board. The stand is a PETG floor cradle with a 20-degree V-saddle and two side cheeks: the board stands level on its tyre and cannot roll, for storage, charging or display. The charge-port plug is a D-shaped TPU push-in that keeps water and grit out of a 3-pin port, with a grip flange and a lanyard tab. The corner guards are 4 mm chamfered TPU pads you stick to the rail corners with double-sided tape. Fits the Onewheel GT: the stand takes the stock 11.5 x 6.5 in tyre, the 7 in Performance Treaded and the 12 in Rally XL. Made to order in our Melbourne workshop.

From A$8Made to order Studio renders, real photos coming

From A$8 for the charge-port plug. Printed to order in Melbourne and shipped Australia-wide; we confirm the final price and lead time before anything is printed.

Get a quote → Email us about this part

On the quote page choose Request a quote (no file needed) and name this part and the option you want.

Black 3D printed V-shaped tyre cradle stand with side cheeks, four small orange chamfered corner guards and an orange D-shaped plug with a pull tab — Studio render: made to order, real photos coming: the tyre stand (PETG), the four rail corner guards and the charge-port plug (TPU).

Order status. The stand is sized from the maker's published tyre sizes. The plug and guards are sized from public port and rail measurements, so we include a 3-size plug coupon and a guard outline template with the first order: check them on your board before we print the final parts.

What does it look like in use?

Renders are computer images of our own design, made from the same model we print. This family is made to order: real photos of our first prints are coming.

A plain grey stand-in board with a cylinder tyre seated in the black stand, orange guards on its rail corners and the plug in a plain port block — **In use (render)**Render: a generic stand-in board in the stand, guards on the rail corners, plug in the port. The board is a plain stand-in, not the product.

Specifications: material, size and what it fits

Spec	Detail
Tyre stand	PETG, 144 x 196 x 48 mm, 20-degree V-saddle with two side cheeks, flat base. 4 walls, 10 % gyroid infill (it carries the whole board). About 218 g. Seats 11.5 x 6.5 in, 11.5 x 7 in and 12 x 7 in tyres with at least 3 mm of side clearance
Charge-port plug	TPU 95A, 19 x 31.5 x 10 mm, D-shaped body 12.0 mm across with a 4.4 mm flat, three 2.6 mm pin holes, 8 mm insertion, 19 mm grip flange, pull tab with a 5 mm lanyard hole. About 2 g
Rail corner guards	TPU 95A, 48.7 x 48.7 x 4 mm, right-angle outline with a curved diagonal and a 45-degree top chamfer; symmetric, so one shape fits all four corners. Tape face flat. About 5 g each, set of 4
Fits	Onewheel GT boards: stand for the stock 11.5 x 6.5 in tyre, the 7 in Performance Treaded and the 12 in S-Series Rally XL (sizes from the maker's published tyre pages). Plug sized from public 3-pin port measurements; guards sized to the flat rail-corner face
Hardware	Not included. Guards: 3M VHB or foam double-sided tape. Plug: a lanyard cord if you want one. Stand: none
Printing	0.24 mm layers on a 0.6 mm nozzle, no supports. Stand flat on its base; plug flange-down; guards tape-face down

Onewheel is a trademark of Future Motion, Inc. These are independent accessories, not affiliated with or endorsed by Future Motion.

How much does it cost?

Guide prices for printed parts, in Australian dollars. Shipping is extra; we confirm the final price, including any business minimum, before printing. Bulk and custom sizes are quoted per job.

Option	From
Charge-port plug, TPU	A$8
Charge-port plug, 2-pack	A$8
Rail corner guards, set of 4	A$8
Tyre cradle stand, PETG	A$38.95
Kit: stand + 4 guards + plug	A$44.95
Fit coupon (3 plug sizes) and guard template	Free with an order

Who it's for

Owners of single-wheel self-balancing boards who want the board parked upright for charging or display, and riders who want the rails and charge port protected.

Get a quote →Bulk or custom enquiry

Safety & use

Installation & use. Designed for the uses described on this page only. Fixings are not included: use the sizes listed, check they are tight before use, and check the parts regularly for wear or damage. Not for safety-critical or overhead load-bearing use. Damage caused by misuse, modification or overloading isn't a fault in the product.

Board. The stand is for storage, charging and display only. Never stand on the board while it is in the stand, and keep the stand clear of the footpad sensor. The plug and the guards do not make the board waterproof: follow the maker's riding and charging instructions, and take the plug out before charging. Remove a guard if it starts to lift.

What is not changed. These parts fit on the outside only. Nothing is opened, modified or re-bolted, and the board's own warranty terms are not affected by us.

This doesn't affect your rights under the Australian Consumer Law.

FAQ

Common questions

Which boards does the stand fit?

Single-wheel boards with an 11.5 to 12 inch tyre up to 7 inches wide. That covers the Onewheel GT with its stock 11.5 x 6.5 in tyre, the 7 in Performance Treaded and the 12 in Rally XL. The tyre rests on the two 20-degree flanks with its bottom clear of the floor of the V, and the side cheeks leave at least 3 mm each side.

Will the charge-port plug fit my port?

It is a 12 mm D-shaped push-in sized from two public measurements of the 3-pin GT port, with a soft TPU body and 2.6 mm pin holes. Because the maker publishes no port drawing, the first order includes a free 3-size coupon (11.8 / 12.0 / 12.2 mm). Push each in, pick the one that seals and still pulls out by the tab, and we print your plugs at that size.

How do the corner guards attach?

With double-sided tape (3M VHB or foam tape, not included) on the flat tape face. The outline is symmetric about its diagonal, so the same part fits all four corners. A 1.2 mm outline template comes with the first order so you can check it sits fully on the flat rail face before taping.

Can I charge the board in the stand?

Yes, that is the point of it: the board stands level on its tyre and cannot roll, so the charge port stays where you can reach it. Take the port plug out first, and keep the stand off the footpad sensor.

Is it waterproof?

No part here makes the board waterproof. The plug keeps grit and splashes out of the port while riding; it is not a seal rating. Follow the maker's instructions for wet conditions.

How do I order?

Use Get a quote and choose Request a quote, naming the stand, plug, guards or the kit and the colours. We confirm the price and lead time before anything is printed.