Parts catalogue · EV charging · Melbourne

Type 2 EV charger plug holster with rain hood + cable dock

A tidy home for a tethered wallbox cable or a portable charger lead. The holster holds the plug by its nose in a 64 mm cup with a rain hood above it and a drain notch below; the dock is a J-hook for the coiled cable. Both screw to the wall with four countersunk holes. Fits standard Type 2 plugs: the cup is sized for the common 63 mm nose and the plug's 70 mm collar rests on the rim, so a smaller nose simply sits a little looser. Send us your plug's nose size if unsure and we size the cup to it. Holster and organiser only: no electrical function, and it does not lock the plug. Printed to order in PETG (under cover) or ASA (outdoor, UV-stable) in our Melbourne workshop.

From A$10.95Made to order Studio renders, real photos coming

From A$10.95 for the cable dock in PETG. Printed to order in Melbourne and shipped Australia-wide; we confirm the final price and lead time before anything is printed.

Get a quote → Email us about this part

On the quote page choose Request a quote (no file needed) and name this part and the option you want.

Black 3D printed wall plate with a round cup and a projecting rain hood, next to a black J-shaped cable hook, both with countersunk screw holes — Studio render: made to order, real photos coming: the holster with its rain hood (left) and the cable dock (right), in black.

Order status. Standard cup is sized for the 63 mm nose that fits standard Type 2 plugs. If you are not sure of your plug's nose size, send it with the order (a ruler across the round insertion end is enough) or ask for the free fit-test rings.

What does it look like in use?

Renders are computer images of our own design, made from the same model we print. This family is made to order: real photos of our first prints are coming.

Black holster on a plain wall holding a generic grey plug stand-in by its nose, with a black cable coil hanging on the dock beside it — **In use (render)**Render: a generic plug stand-in in the cup and a plain cable coil on the dock. The plug, cable and wall are stand-ins, not products.

Specifications: material, size and what it fits

Spec	Detail
Material	PETG for a garage or carport under cover; ASA for walls in direct sun (UV-stable). Black as standard, other colours on request. 0.20 mm layers, 4 walls, 25 % gyroid infill, no supports
Holster	110 x 150 mm wall plate, 5 mm thick, cup bore 64 mm and 38 mm deep (default nose size 63 mm), 16 mm slot at the top of the cup so the latch hook is never trapped, drain notch at the bottom, rain hood projecting 80 mm with side cheeks. About 116 g
Cable dock	J-hook 60 mm wide with a 70 mm arm and 28 mm lip, gusseted under the arm. Takes charging cables from 9.8 to 22.5 mm diameter (single-phase to 63 A three-phase). About 56 g
Fits	IEC 62196-2 Type 2 vehicle connectors (the standard AC charging plug in Australia and Europe) with a nose up to 63.5 mm across; the 70 mm collar lands on the cup rim. Other nose sizes: tell us the measurement, or ask for the free 4-ring fit coupon (57 / 60 / 63 / 65 mm)
Mounting	Four countersunk holes in the holster and two in the dock for 4-5 mm screws. Screws and wall plugs are not included: use fixings suited to your wall (masonry anchors, stud screws)
Not included / not a function	No electrical parts, no plug lock, no cable. Holds and organises the plug and lead only
Printing	Plate flat on the bed with the cup and hood rising; the dock prints on its side so its layers run along the load. Watertight meshes, no bridges over 10 mm

Type 2 is the IEC 62196-2 connector standard. Charger and vehicle brands named by customers are trademarks of their owners; this is an independent accessory, not affiliated with or endorsed by any of them.

How much does it cost?

Guide prices for printed parts, in Australian dollars. Shipping is extra; we confirm the final price, including any business minimum, before printing. Bulk and custom sizes are quoted per job.

Option	From
Cable dock, PETG	A$10.95
Cable dock, ASA (outdoor)	A$18.95
Plug holster with rain hood, PETG	A$20.95
Set: holster + dock, PETG	A$32.95
Plug holster with rain hood, ASA (outdoor)	A$37.95
Set: holster + dock, ASA (outdoor)	A$58.95
Fit coupon (4 rings, 57-65 mm)	Free with an order
Custom nose size (your measurement)	No extra charge

Who it's for

EV owners with a home wallbox or a tethered cable, strata and fleet car parks, and electricians or installers who hand over a tidy install.

Get a quote →Bulk or custom enquiry

Safety & use

Installation & use. Designed for the uses described on this page only. Fixings are not included: use the sizes listed, check they are tight before use, and check the parts regularly for wear or damage. Not for safety-critical or overhead load-bearing use. Damage caused by misuse, modification or overloading isn't a fault in the product.

EV charging. This is a holster and cable organiser with no electrical function. Follow your charger maker's instructions for charging, never use a damaged plug or cable, and keep the plug out of standing water. Mount it into fixings suited to the wall and check the screws now and then.

Outdoors. Choose ASA for walls in direct sun; PETG is for covered positions. Printed plastic is not fire-rated: keep it clear of heat sources.

This doesn't affect your rights under the Australian Consumer Law.

FAQ

Common questions

Will it fit my plug?

It fits standard IEC 62196-2 Type 2 vehicle connectors, the plug on every AC wallbox and portable charger sold in Australia and Europe. The cup is sized for a 63 mm nose with half a millimetre of clearance; the plug's 70 mm collar rests on the rim, so a smaller nose still sits fine, just a little looser. If you are unsure, send us your plug's nose measurement or ask for the free fit-test rings and we size the cup to match.

PETG or ASA?

PETG for a garage or a covered carport. ASA for a wall in direct sun: it is UV-stable and does not go brittle or yellow. ASA costs more because the filament does, and it is printed in an enclosed printer.

Does it lock the plug or do anything electrical?

No. It holds the plug by its nose under a rain hood and keeps the cable off the floor. There are no electrical parts and no lock. Charging stays exactly as your charger maker intended.

What screws do I need?

Four 4-5 mm screws for the holster and two for the dock, with wall plugs or anchors suited to your wall. Fixings are not included because every wall is different; the holes are countersunk.

Can you change the size or colour?

Yes. The cup diameter, plate size and hood depth are parameters in our model, and any filament colour we stock can be used. Custom nose sizes are no extra charge.

How do I order?

Use Get a quote and choose Request a quote, naming the option (dock, holster or set) and PETG or ASA. We confirm the price and lead time before anything is printed.